Thank you for visiting WANBO SHOP! welcome to consult all item’s price, especially about the international freight of above 20Kg, maybe there are some discount for you. because the price is not fixed! WANBO SHOP will 100% reply to you!
The main factors affect the sound quality of vacuum tube amplifier
1. Single-ended and push-pull circuit
At the end of the power amplification, amplification of push-pull is easier to get high power output, because push-pull is a vacuum tube amplifier “+” signal, a vacuum tube amplifier “-” signal, and then superimposed, so large distortion. Single-ended amplifier is a vacuum tube amplifier “+, -” signal, does not need the signal superposition, therefore less distortion. The sound Single-ended than push-pull good, especially in some minor details. However, Single-ended is difficult to obtain high power output, with vacuum tubes of the same type, Single-ended can do 10W, while push-pull is easy to do 30W, Single-ended to obtain large power will have to pay more price.
2. push-pull end power amplifier of vacuum tube different connections
push-pull the end of the power amplifying vacuum tube usually have three connections: triode form, super linear form and standard form. Theoretically speaking, the triode form by minimum distortion, output power is minimum; standard form get larger distortion, power is also the maximum; between super linear form between.
3. Affect the power transformer and output transformer of sound
High quality vacuum tube amplifier inseparable quality transformers, power transformers currently technically no trouble, the output transformer is the decision of the vacuum tube amplifier sound quality is the key. Because regardless of the output transformer selection is good, how sophisticated technology, both methods exist to avoid leakage inductance and stray capacitance components, resulting phase distortion. Output transformer as inductive element, to the transmission signals of different frequencies have different inductance. Therefore, the output of the transformer will be different in different voices lead. No high-quality output transformer, other aspects of the production of better quality vacuum tube amplifier is also meaningless.
Cayin MT-35MK2 Tube amplifier Tube earphones amplifier EL34x 4 2x32W have all-powerful power match 90~270V
1. A selection of high-quality output EI type transformers and toroidal power transformers, individually packaged, to prevent interference.
2. The selection of a tube of Russia SOVTEK 12AX7, two domestic 12AU7, four pre-EL34.
3. The independent pre-shielded box, the whole scaffolding manual welding, the internal interference completely eliminated.
4. Using two high-quality broadband sound EI output transformer.
5. specially manufactured for low magnetic leakage, high efficiency toroidal power transformer.
6. The preamp uses two 12AU7 vacuum tube and a Russian electro-harmonix 12AX7EH vacuum.
7. After the level four EL34 tubes used to do push-pull power amplifier class AB1.
8. With headphone output.
9. Easy installation of the plug-type vacuum tube shield.
Because photographic cause color differences, please know!
Rated output power 2x32W (RMS 8Ω)
Frequency response 18Hz~40kHz
Input Sensitivity 290mV
Input impedance 100kΩ
Output impedance 4Ω,8Ω
Headphone output impedance32Ω~300Ω
Tube EL34x4 12AU7x2 12AX7EH
Power supply 220V±5% 50Hz
Power consumption 260W
Weight 13.5kg Vacuum tube amps the use of attention:
1. Disable output short circuit and output load, before you start you must first connect speakers or headphones, the best is always keep them connected,
2. Start with minimal volume,
3. The supply voltage should be stable, with the use of conditional HiFi clean power for better protection and sound,
4. When the vacuum tube amplifier operating temperature is high, pay attention to ventilation, not to touch hot tube,
5. Do not put water on a hot vacuum tubes,
5. Do not put water on a hot vacuum tubes,
6. Boot and shutdown interval of 5 minutes,
7. Do not over 6 hours of continuous work,
8.6 ohm speaker connected to the 4 ohm, 8 ohm interfaces are available,
9. vacuum tube amplifier sound 40% depending on the power amplifier tube quality, 40% depends on the quality of output transformer, 10% depends on other electronic components quality, 10% depending on the manufacturing process,
10. power supply voltage can be free custom (please consult).